Polytech Asia Pte. ltd.

Mumbai, Singapore

We are offering taber stiffness tester.Incorporated in the taber v-5 stiffness tester is a bi-directional pendulum weighing system. providing an accurate and responsive method for measuring small load increments, this system is a critical component for determining material stiffness or resiliency. nine (9) distinct ranges permit testing of materials that are extremely lightweight and flexible (such as cellophane or thin metallic foils) to items that are very rigid (such as plastics). For test ranges 2 - 9, specimens are mounted on the taber v-5 stiffness tester using a clamping system. located on the pendulum, the lower faces of the specimen clamp jaws are exactly on the center of rotation. this ensures a constant test length and deflection angle for accurate and repeatable results. both jaws of the specimen clamp are adjustable, so the test specimen can be positioned precisely in the center regardless of material thickness. Force is applied to the lower end of the specimen by a pair of rollers. The rollers, which are attached to a driving disc located directly behind the pendulum, push against the test specimen and deflect it from its vertical position. the pendulum applies increasing torque to the specimen as it deflects further from its original position. the test point reading occurs when the pendulum mark aligns with the appropriate driving disc mark (7 12 or 15), which points to the stiffness reading on the dial point. the final reading will depend on the range in which the test is being conducted and what scaling factor to use. the instrument outputs the moment load applied to the test specimen in taber stiffness units (g cm). Note: the right hand roller includes a ratchet stop mechanism that greatly reduces the potential for inter-operator error caused by over or under-tightening. the travel on the right hand assembly automatically stops when the roller contacts the specimen.

We are offering inclined plane friction tester. The hanatek inclined plane friction tester is a low cost but extremely accurate instrument for determining the static friction coefficient of flat surfaces.Designed for use in the packaging industry to measure the static slip of unprinted carton board, printed cartons or plastic films and their coatings, the instrument is suitable for measuring other products including leather, textiles and paper.Results are displayed in both coefficient of friction and slip angle with batch analysis and can be output to the optional hanatek results printer.The operation of the device is exceptionally simple, simply cut two samples attach one to the platen and one to the measurement sled. The instrument will raise the platen until the static slip force value is determined. The instrument displays the results in coeficient of friction and slip angle.For measuring dynamic friction please refer to our advanced friction testerfeaturesmultiple tests with statistical analysissimply measures static coefficient of frictionaccurate slip measurement- readout to 0.1precision servo motor for repeatable readingsauto stop and auto-platen returnavailable with a choice of sleds for relevant astm tappi standardsresults displayed in cof and slip angleresults label printer

We are offering rub and abrasion tester. The hanatek rub and abrasion tester (ink rub tester) brings new levels of repeatability and convenience to testing the durability of inks and coatings on any printed material.The instrument is used for testing the scuff, marking and rub resistance of cartons, films and commercial printed material.This comparative test works by abrading a printed sample against a reference material under known conditions.The results can be used to identify alternative substrates, better ink and coating formulations or the suitability of finished cartons, films or printed books, magazines and promotional materials.The hanatek rub and abrasion tester can be programmed for the required number of cycles, enabling it to be run concurrently with other laboratory tests.Optional test attachments offer the ability to conduct tests under harsher conditions and can be used to check the solvent resistance or the cure of uv inks.Featuresfully automated touch screen operationchoice of weights to comply to bs3110air jet waste removaladditional attachments for scratch test or wet rub testprogammed test cycles allow tests be to run unsupervised.Free two year warrantyoptional results printer to enable test parameters to be documented on retained samples

We are offering cap torque testers.Series tt01 cap torque testers are designed to measure application and removal torque of bottle caps up to 100 lbfin [11.5 nm]. Adjustable posts effectively grip a broad range of container shapes and sizes, while optional flat and adjustable jaws are available for unique profiles. A rugged aluminum design, and simple, intuitive operation allow for use in laboratory and production environments. Class-leading accuracy of 0.3% and blazingly fast sampling rate of 7, 000 hz ensure reliable and consistent test results, even in quick-action applications. Password protection is provided to prevent unauthorized changes to settings and calibration. The tt01 includes a range of sophisticated productivity-enhancing features, including usb, rs-232, mitutoyo, and analog outputs, automatic data output and zeroing upon cap removal, memory storage for 1, 000 readings, passfail indicators and outputs, and more. First second peak torque detection is useful for measuring slip and breakaway torques for tamper evident closures. Series tt01 testers include mesurtm lite data acquisition software. Mesurtm lite tabulates continuous or single point data. Data stored in the tt01s memory can also be downloaded in bulk. One-click export to excel allows for further data manipulation.