Polytech Asia Pte. ltd.

Mumbai, Singapore

We offer Taber Abraser. Taber tests involve mounting a flat specimen approximately 100mm square or round to a turntable platform that rotates on a vertical axis at a fixed speed. The standard material thickness that can be evaluated with the Taber Rotary Abraser is 6.35 mm (materials greater than 6.35 mm but less than 40 mm can be tested with optional accessories). Two genuine Taber abrasive wheels, which are applied at a specific pressure, are lowered onto the specimen surface. Characteristic rub-wear action is produced by contact of the test specimen against the sliding rotation of the two abrading wheels. As the turntable rotates, the wheels are driven by the sample in opposite directions about a horizontal axis displaced tangentially from the axis of the sample. One abrading wheel rubs the specimen outward toward the periphery and the other, inward toward the center while a vacuum system removes loose debris during the test. The wheels traverse a complete circle on the specimen surface, revealing abrasion resistance at all angles relative to the weave or grain of the material. The resulting abrasion marks form a pattern of crossed arcs in a circular band that cover an area approximately 30 cm2 Each turntable has dual abrading arms that are precision balanced. Independently operated, the abrading arms can be raised (or lowered) to mount or inspect specimens. Each arm is loaded for 250 gram pressure against the specimen, exclusive of the weight of the wheel. To increase the load to 500 or 1000 grams, a mount for auxiliary weights is located on the outside of the abrading wheel bearing assembly. This location ensures that weights are concentric with the abrading wheel. A stud on the rear end of the abrading arm is used to carry an optional counterweight (used to reduce the load by 50, 125 or 175 grams).

We are offering multi finger scratch.He multi-finger scratch mar tester includes a pneumatically driven, moveable platform to which the test specimen is mounted. the platform moves in a linear fashion, and is operated by a control knob for single or multiple pass testing. an electronic timer displays the rate of speed, which can be controlled by reducing or increasing air pressure. A gantry supports five independent splined-fingers, which provide a constant, vertical load on interchangeable scratch tips. the gantry system includes a handle to raise and lower the arms. in addition, five support rests are incorporated to allow one or more arms to be moved to an upright, rest position such that the arm does not contact the specimen during testing. Individual weights of varying loads mount to the top of each arm finger to exert a standard force on the surface of the test material. Each instrument includes a weight set of 2n, 3n, 4n, 5n, 6n, 7n, 10n, 15n and 20n loads.

We are offering stripping machine . The cable stripping and twisting machine st215 was specially developed for thin cables. It features an approved four blade system, which provides accurate and exactly repeated stripping of cables. The coating is removed by cutting with four rotating blades and strip-off in one single step. This innovative procedure allows processing of: * coaxmicro-coax cables* teflon or kapton coated cables* sucoform sm86 cables from huber & suhner further more, wires are twisted during the stripping process. The high precision avoids damage to wires, dielectric or shield. In addition, a centering unit allows very high precision stripping for high end applications. The centering unit is infinitely adjustable and assures that the cable is centered respectively to the cutting blades. User influences regarding the stripping quality are eliminated.Precision blade diameter control with a micrometer scale, allows a quick set-up of diameter. The locking screw of the diameter adjusting system makes the machine available even for military, aerospace and medtech applications. The quick length control is equipped with a sensor which initiates the stripping process. The high quality of the product guaranties a precise repetitiveness. the all new st215w features two additional functions: * the rotation of the stripping head can be stopped prior to pull-off. This allows to twist or not the strands.* the second new function is the adjustable wayback. This function will open the blades a little prior to pull-off. This increases the stripping quality, especially when the wires have important diameter tolerances.

We offer Linear Abraser.The Taber Linear Abraser incorporates a horizontal arm that reciprocates in a linear motion. Attached to the end of the arm is a precision bearing spline shaft that creates a 'free-floating' test system and permits vertical movement. The test attachments are affixed to the bottom of the spline shaft and a weight support is mounted to the top. As the horizontal arm strokes back and forth, the test system raises or lowers vertically as the test attachment follows the contours of the specimen. A laser alignment guide assists with specimen set-up to ensures the abradant travels over the desired area. Adjustable settings enable the user to select the speed, stroke length and test load. The Linear Abraser includes six preset speed buttons, along with the ability to adjust the speed from 2 to 75 strokes per minute. Eleven stroke lengths are standard ranging from 0.2 inch to 4.0 inch. The base load of the free-floating" test system is 350 grams and consists of the test attachment spline shaft and weight support. Three 250g weight discs are supplied with the instrument and optional weight discs ranging from 10 to 250 grams can be added to the weight support to increase the test load to approximately 2100 grams. Optional accessories can be also be used to decrease the load. For example, an 150mm aluminum spline shaft and plastic Wearaser Collet Kit can bring the minimum load on the sample to as low as 60 grams. Taber's Linear Abraser is programmable to 999, 999 cycles, but caution must be used as the abradant may wear prior to the end of the test. The Wearaser collet assembly is supplied with each Taber Linear Abraser, along with CS-10 and H-18 Wearaser abradants. The size and shape of a pencil eraser, the Wearaser is made using the same high quality Taber abrasive media found in our Genuine Taber abrading wheels.

We offer Profile plus Thickness.The PROFILEPlus&trade Thickness instrument meets or exceeds paper industry standards to provide the accuracy and repeatability you need from this critical test parameter. To assist in controlling the production process, each measurement is made quickly, so data is received in a timely manner. &bull Self cleaning measurement area.&bull Fast, easy calibration.&bull Simplified parallelism system. Meets the following industry standards:TAPPI Test Methods T411ISO Standards 534, 3034, 12625

We offer series 5 advanced digital force gauges.Series 5 advanced digital force gauges are designed for tension and compression force testing in numerous applications across virtually every industry, with capacities from 0.12 lb to 2, 000 lbf (0.5 n to 10 kn). The gauges feature an industry-leading sampling rate of 7, 000 hz, producing accurate results even for quick-action tests. Accuracy is 0.1% of full scale, and resolution is 15000. A large, backlit graphics lcd displays large, legible characters, while the simple menu navigation allows for quick access to the gauges many features and configurable parameters. Data can be transferred to a pc or other data collector via usb, rs-232, mitutoyo (digimatic), or analog outputs. On-board data memory for up to 1, 000 readings is included, as are statistical calculations and output to a pc. Integrated set points with indicators are ideal for pass-fail testing and for triggering external devices such as an alarm, relay, or test stand. The gauges are overload protected to 150% of capacity, and an analog load bar is shown on the display for graphical representation of applied force. The series 5s averaging mode addresses the need to record the average force over time, useful in applications such as peel testing, while external trigger mode makes switch activation testing simple and accurate. An ergonomic, reversible aluminum design allows for hand held use or test stand mounting for more sophisticated testing requirements.

These table top densitometers display transmission density and density difference. The tbx1500 also calculates positive and negative dot areas. Single-step measurement of %opacity, %transmission, and transmission optical density the tobias tbx1000 and tbx1500 transmission densitometers measures transmission optical density. The tbx1500 also calculates positive and negative dot area. The unite have been designed for user convenience and error-free measurement. The data can be uploaded to a spreadsheet via the usb port using an optional data transfer program (pn a2128). To meet special requirements an optional filter carrier may be used allowing supplementary filters to isolate a portion of the spectrum that may be of interest. the tbx1000 and tbx1500 have been designed for user convenience and error-free measurement. Table illumination facilitates film placement and the entire operation requires only one hand, leaving the other free for note taking or sample repositioning. The unit has both an absolute mode and a relative mode, which can be used for comparing the measured values to a previously stored value for consistent process control. * b&w transmission densities* calculates positive and negative dot area (tbx1500)* soft key menu operation* 7 inch throat to measure large samples* readings are very repeatable with a large degree of accuracy* usb port standard* software calibration* optional band pass filter* switchable led table lamps* cost effective and affordable quality control system

The jis l1099 b1 + b2 is one of the most common standards for measuring the moisture vapour transmission rate of fabrics and textiles, especially for the outdoor market. Gintronic idc-6 is offering for this a state of the art tester, with automatic temperature control of the waterbath and the ambient temperature. With the idc-6 you can measure 6 samples at the same time. The gintronic idc-6 also conforms to iso 15496. applications: for the determination of the moisture vapour transmission rates of fabrics, foils, films and other sheet materials based on the gravimetric inverted drycup method.Conforms to jis l1099 b1 + b2 and iso 15496. For running a test no external oven or temperated room is required.

We offer Coaxial Cable Stripping Machine St730.The ST730 meets all the requirements for a flexible wire processing machine. Challenging stripping of coax- or triaxial cable is a breeze for the ST730 to handle. Of course, multi-conductor cable or single wire with special insulation such as Kapton or Teflon can also be processed. The handling is very easy: insert the cable and the sensor will start the stripping cycle. The ST730 strips the outer jacket, the shield as well as the dielectric within seconds very precisely.Set up times are practically eliminated because when selecting stored cable parameters the machine sets itself up. The job is further simplified through the build in counter and the ability of setting sequences. The intuitive operation allows for quick and reliable machine settings when changing to a different cable. Stripping parameters can be protected by selecting a password through authorized personnel. The stripping machine ST730 impresses, due to its high quality workmanship, longevity and guaranties the highest flexibility with sustained productivity!

We offer Color Touch Pc.Count on the Color Touch PC when color decisions matter.Quick. Exact. Versatile. When making decisions on whether a product meets customer specifications, the need to have all the data to evaluate the product is necessary. With swing-in calibration, primary calibration, Color Touch PC software, sample viewing, and optional equipment, the Color Touch PC boasts functionality that is far beyond standard color evaluation. * Samples may be measured under 4 different calibrated light sources or 2 user defined sources.* Device is capable of sampling whiteness under different fluorescing conditions.* Color data may be calculated with 6 color spaces, 10 illuminants and 2 observers.* The Color Touch PC software provides setup flexibility to allow customer specific data presentations In today world of strict standards and high demands, the data needed to assess whether a product meets customer specification is imperative when making decisions. The Color Touch PC can be trusted to accurately gather this vital data. Meets the following industry standards:ISO Standards 2469, 2470, 2471, 3688, 5631, 9416, 11475, 11476, 12625, 22754, 22891TAPPI Optical Methods T519, T525, T527, T534, T560PAPTAC E.1, E.2, E.5, E.8

We offer Esm303 Motorized Test Stands with Pc Control.The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMe force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.With generous travel, clearance, and depth dimensions, a wide range of tests can be performed, including break testing, cycling, limit testing to a load or distance, loadholding, elongation testing, tensile testing, compression testing, and more. Satisfy various test methods through an easy-to-use menu, allowing the configuration of test speed, force and distance limits, cycling, preload, and many other functions, all protected by a password. Save up to 50 profiles to accommodate a range of test methods.When the ESM303s clearance is insufficient for the application, its modular mechanical design allows for single- and double-column extensions. Modularity extends to the controller functions as well. Individual functions, such as travel measurement, cycling, loadholding, etc., may be purchased either upfront or enabled in the field through an activation code. This a-la-carte platform allows for custom configuration as appropriate for the application and budget.Force and travel data can be output to a PC for graphing and analysis using MESURgauge software. Or, fully control the stand by a PC through a custom-written program with ASCII communication.